Show simple item record

dc.contributor.advisorTutuncu, Azra
dc.contributor.advisorYang, Yuan
dc.contributor.authorMcDowell, Bryan P.
dc.date.accessioned2018-05-31T15:31:54Z
dc.date.accessioned2022-02-03T13:12:12Z
dc.date.available2018-05-31T15:31:54Z
dc.date.available2022-02-03T13:12:12Z
dc.date.issued2018
dc.identifierMcDowell_mines_0052N_11516.pdf
dc.identifierT 8512
dc.identifier.urihttps://hdl.handle.net/11124/172343
dc.descriptionIncludes bibliographical references.
dc.description2018 Spring.
dc.description.abstractNuclear magnetic resonance (NMR) has become an increasingly important tool for estimating porosity, permeability, and fluid characteristics in oil and gas reservoirs since its introduction in the 1950s. While NMR has become common practice in conventional reservoirs, its application is relatively new to unconventional reservoirs such as the Eagle Ford Shale. Porosity and permeability estimates prove difficult in these exceptionally tight rocks and are routinely below the detection limit and/or resolution of low frequency (2 MHz or less) NMR. High frequency (400 MHz) NMR has been applied to address these issues; however, previous studies have been limited to crushed rock samples or millimeter-sized core plugs. In response, a custom-built NMR probe has been constructed, capable of measuring 0.75-inch diameter, 0.45-inch length core plugs at 400 MHz, to determine if larger core plug sizes yield higher resolution T2 distributions in the Eagle Ford Shale. The tool is composed of two primary elements, the structural framework and the radio frequency circuit. Each element was designed and constructed iteratively to test various layouts while maintaining functionality. The probe's structural design was initially based on retired, commercial probes then modified to operate within a Bruker Ascend 400WB NMR spectrometer. Designs were drafted and 3D-printed multiple times to determine proper physical dimensions and clearances. Once designs were deemed satisfactory, structural components were manufactured and assembled to create the structural framework. A radio frequency circuit was then built to measure T2 distributions at the desired frequency and sample size. Multiple inductor designs and capacitor combinations were tested until a stable circuit, capable of matching impedance and tuning to the proper frequency, was achieved. The probe's stability and data quality were then confirmed by measuring the NMR spectra of deuterated water in a Teflon container. The NMR probe was validated by comparing high frequency (400 MHz) data acquired in-house to low frequency (2 MHz) data measured at a commercial laboratory. Twelve core plugs (0.75-inch diameter, 1-inch length) were cut from two Eagle Ford Shale subsurface cores located in Gonzales and La Salle counties, Texas. Low frequency T2 distributions were measured twice: first after drying core plug samples in a vacuum oven and again after spontaneous imbibition with various brine solutions (deionized water, 8 wt.% KCl, or 17.9 wt.% KCl) for one week. These contrasting saturation states were applied to highlight immovable water in the core plugs. For high frequency data measurements, samples were trimmed to 0.45-inch lengths to fit inside the newly-built NMR probe, leaving two sub-samples for each of the original core plugs. T2 distributions were first acquired "as-is" (e.g., without drying or imbibition). After as-is data acquisition, samples were dried in a vacuum oven then allowed to spontaneously imbibe the same brine solutions used in the low frequency study. T2 distributions were measured again after imbibition and compared to the low frequency data acquired by the commercial laboratory. Qualitatively, high frequency T2 distributions resemble low frequency data; however, the absolute T2 values are routinely higher by one order of magnitude. The difference may be caused by data acquisition, data processing, fluid-rock interactions, magnetic field inhomogeneities, or some combination thereof. In spite of not attaining the higher-resolution T2 distributions desired, the project still provides a proof-of-concept that T2 relaxation times can be measured in conventional-sized core plugs using 400 MHz NMR. Although limited in its outcomes, the study delivers promising results and elicits future research into utilizing high frequency NMR spectroscopy as a petrophysical tool for unconventional reservoirs.
dc.format.mediumborn digital
dc.format.mediummasters theses
dc.languageEnglish
dc.language.isoeng
dc.publisherColorado School of Mines. Arthur Lakes Library
dc.relation.ispartof2018 - Mines Theses & Dissertations
dc.rightsCopyright of the original work is retained by the author.
dc.subjecthigh field NMR
dc.subjectprobe design
dc.subjectT2 relaxation
dc.subjecthigh frequency NMR
dc.subjectEagle Ford
dc.subjectself diffusion coefficient
dc.titleApplication of a custom-built, 400 MHz NMR probe on Eagle Ford Shale core plug samples, Gonzales and La Salle counties, Texas
dc.typeText
dc.contributor.committeememberKazemi, Hossein
dc.contributor.committeememberPrasad, Manika
thesis.degree.nameMaster of Science (M.S.)
thesis.degree.levelMasters
thesis.degree.disciplinePetroleum Engineering
thesis.degree.grantorColorado School of Mines


Files in this item

Thumbnail
Name:
McDowell_mines_0052N_11516.pdf
Size:
22.09Mb
Format:
PDF
Thumbnail
Name:
supplemental.zip
Size:
9.281Mb
Format:
Unknown

This item appears in the following Collection(s)

Show simple item record